How To Measure Your Wrist For A Watch

To measure fit without a measuring tape, use a thread or string when your arm is laid flat on a surface and allow both ends of the string to come in contact. Wondering if a standard size bracelet, bangle or watch wears nicely on your wrists?the best way to be sure is to know your actual wrists size or circumference.

Please take a moment to measure your wrist before ordering

Don't pull it too tight.

How to measure your wrist for a watch. Put a watch ruler in the watch while it is closed. To measure the size of your wrist for a bracelet or watch, wrap flexible measuring tape around your wrist in the exact area where you want the item to go. Open your hand (doing so will ensure you get the real size of your wrist when it’s the largest) snuggly wrap a measuring tape around your wrist.

Adjust accordingly to make sure it is wrapped around your wrist loosely/tight enough for your personal comfort. Measure the case size of the watch. To measure your wrist for a bangle, start by holding your hand in the shape that you would when putting on a bangle.

Measurement off wrists is a pretty straight forward task, depending on what wearable goes on your wrists, we have prepared a wrist size guide with steps to help you diy at home. Take a flexible ruler and wrap it around your wrist. Finally, wrap the measurement tape around your wrist and voila!

If you don't have the ability to print out (and cut out) the printable tool, you can also measure your wrist using a tape measure or ruler, paper, and pen. Wrap the measuring tool around your wrist. This will give you a measurement so you can choose the best diameter for your wrist.

(if it helps, use some tape to hold the wider part in place.) Take the actual measurement where the tape meets itself. Measure the long end of the strap from the spring pinhole to the second or third hole on the watch band.

Line up the arrows on the case with a number. Go to the leather strap sizes page, and see where this measurement fits in the optimal size range. Make sure that tool size does not slide away check the number that the arrow will be pointing.

Measure your wrist with the tape measure slightly around the bottom of the palm if you prefer a looser fit. This is the measurement of the face of your watch. Bring all your fingers together, specifically being sure to bring your thumb in so that it is touching your pinkie finger.

Smaller than 5 to 6 inches (12 to 15 cm), choose a diameter 38 millimeters or less. Measure the case from one end to the other of the central portion of the watch, without the crown or any pusher. This is your comfortable wrist measurement.

Whether investing in a new watch or your first watch for your collection, these measurements will come in handy for purchasing an additional band or retrofitting a band you may already have to a new watch case. Mark where the two ends meet then lay the thread out flat on a ruler and measure the distance. To know how big your wrist is, you pick up a flexible plastic tape from a local store or from a seamstress and wrap it around your wrist, but over the wrist bone(the largest portion of your wrist).

It should fit comfortably but not loose. Between 6 and 7 inches (15 to 17 cm), pick a 38 to 42 millimeter diameter. Measure up past your wrist bone if you like your watch to have a snug fit.

You’ve measured the circumference of your wrist. Place the cut shape on your wrist where you would be placing your watch face and warp the paper size too tightly on your wrist. This value is especially important if you are measuring your wrist size for a watch or a bracelet.

On a simple watch with just a single crown at 3 o’clock (like most watches), it’s easiest to measure the case from 2 o’clock to 8 o’clock. Then, record the number on the tape that overlaps with its 0 end and add roughly 0.5 inches, so your watch or bracelet isn't too snug. The thickness of your watch case does play a role in the overall.

The place the string flat on a ruler and measure the length. Find your watch head size by using a ruler or check the manufacturer for information. 1) find yourwrist size by wrapping a tape measure or a piece of string around your wrist.

Put the end of the tape right in the middle of your wrist. Cut out the length chart below along the dotted lines. However, if you’re looking for our advice, it would be to put it just below the wrist bone.

Hold your watch face on its side and measure from one spring pinhole to the other. Comfort and fit are more important than personal style when choosing a watch strap. Hold the strip just below where your wrist bone sits and around where you would normally wear the band, wrap it around your wrist and line that up with the sizes of your watch model.

Simply wrap the piece of string around your wrist ( not too tightly) where you would normally wear a watch and either mark or hold the string when it meets the starting point. Bring the ends of the tape closer and read the difference between the numbers on the tape. Place the case shape on your wrist where you would normally have the watch face, then wrap the paper tool tightly around your wrist.

About the position of the tape, you can put it where your watch would generally be. This is the size band you should get. Take into consideration how tight you want your watch to be.

Read the size on the measuring tape, preferably in inches or centimeters. This is usually more on your arm and a little below the wrist bone. To determine the length of your watch band follow these 4 steps.

We measure everything in inches these days, but the standardization for watches is in millimeters. See ‘kohl’s case sizing guide’ if you need help. Now measure the short strap of your watch from the bottom of the buckle to the spring pinhole.

If you are using a fabric tape measure, read the measurement as exact as possible and skip to step number 7. To measure your wrist for watch straps, use the measuring tape as described earlier.

How to Choose the Best Watch Size for Your Wrist in 2020